Rebar is bought by weight and used by length, and the gap between the two is where estimates go wrong. Three things account for almost all of it: the bar schedule, the lap lengths, and the offcut you cannot avoid when 12 metre bar meets a 4.5 metre element.
သံချောင်းကို အလေးချိန်ဖြင့် ဝယ်ပြီး အရှည်ဖြင့် သုံးသည်။ ထိုနှစ်ခုကြား ကွာဟချက်သည် ခန့်မှန်းချက်များ မှားရာနေရာ ဖြစ်သည်။ သုံးခုက အားလုံးနီးပါးကို ဖြစ်စေသည် — ချောင်းဇယား၊ ထပ်ရာအရှည်များ၊ နှင့် ၁၂ မီတာ ချောင်းသည် ၄.၅ မီတာ အစိတ်အပိုင်းနှင့် ဆုံသောအခါ ရှောင်လွှဲ၍ မရသော အပိုကျန်။
How do I convert length to weight?
အရှည်ကနေ အလေးချိန်ကို ဘယ်လိုပြောင်းမလဲ။
Use the mass per metre for the diameter. As a working set: 10 mm is about 0.62 kg/m, 12 mm about 0.89, 14 mm about 1.21, 16 mm about 1.58, 20 mm about 2.47, 25 mm about 3.85 and 32 mm about 6.31. Multiply by the total metres. A 12 metre bar at 16 mm is therefore about 19 kg.
အချင်းအတွက် တစ်မီတာလျှင် ဒြပ်ထုကို သုံးပါ။ လက်တွေ့ စာရင်းအဖြစ် — ၁၀ မီလီမီတာသည် ၀.၆၂ kg/m ခန့်၊ ၁၂ မီလီမီတာ ၀.၈၉၊ ၁၄ မီလီမီတာ ၁.၂၁၊ ၁၆ မီလီမီတာ ၁.၅၈၊ ၂၀ မီလီမီတာ ၂.၄၇၊ ၂၅ မီလီမီတာ ၃.၈၅၊ ၃၂ မီလီမီတာ ၆.၃၁။ စုစုပေါင်း မီတာနှင့် မြှောက်ပါ။ ထို့ကြောင့် ၁၆ မီလီမီတာ ၁၂ မီတာ ချောင်းသည် ၁၉ ကီလိုခန့် ဖြစ်သည်။
Why does my calculation not match some listings?
ကျွန်တော့် တွက်ချက်မှုက အချို့စာရင်းနဲ့ ဘာကြောင့် မကိုက်လဲ။
Because some of our rebar listings carry weights that do not match the diameter and length shown — the same 16 mm by 12 metre bar appears at three different figures on three listings. Work from the diameter and the mass per metre, and confirm the weight with the counter before ordering by it. The bar itself is standard; the recorded weight is not reliable on every line.
ကျွန်ုပ်တို့ သံချောင်း စာရင်းအချို့တွင် ဖော်ပြထားသော အချင်းနှင့် အရှည်နှင့် မကိုက်ညီသော အလေးချိန်များ ပါသောကြောင့် ဖြစ်သည် — ၁၆ မီလီမီတာ x ၁၂ မီတာ ချောင်းတူသည် စာရင်းသုံးခုတွင် တန်ဖိုးသုံးမျိုးဖြင့် ပေါ်သည်။ အချင်းနှင့် တစ်မီတာလျှင် ဒြပ်ထုမှ တွက်ပြီး၊ အလေးချိန်ဖြင့် မမှာမီ ကောင်တာနှင့် အတည်ပြုပါ။ ချောင်းကိုယ်တိုင်သည် စံဖြစ်ပြီး၊ မှတ်တမ်းတင်ထားသော အလေးချိန်သည် စာကြောင်းတိုင်းတွင် မယုံကြည်ရပါ။
What is a lap and why does it add to the quantity?
ထပ်ရာဆိုတာဘာလဲ၊ ဘာကြောင့် ပမာဏ တိုးစေလဲ။
Where two bars have to act as one continuous bar, they overlap by a specified length so the force transfers through the concrete between them. That lap is dead length as far as the structure is concerned but it is steel you have to buy. On a long element the laps can add a noticeable percentage to the total, and the bar schedule should already include them.
ချောင်းနှစ်ခုသည် ဆက်တိုက် ချောင်းတစ်ခုအဖြစ် အလုပ်လုပ်ရမည့်နေရာတွင် ၎င်းတို့ကြားရှိ ကွန်ကရစ်မှတဆင့် အား ကူးပြောင်းနိုင်ရန် သတ်မှတ်အရှည်ဖြင့် ထပ်ထားသည်။ ထိုထပ်ရာသည် တည်ဆောက်ပုံအရ အသုံးမဝင်သော အရှည်ဖြစ်သော်လည်း ဝယ်ရမည့် သံမဏိ ဖြစ်သည်။ ရှည်လျားသော အစိတ်အပိုင်းတွင် ထပ်ရာများသည် စုစုပေါင်းသို့ သိသာသော ရာခိုင်နှုန်း တိုးစေနိုင်ပြီး၊ ချောင်းဇယားတွင် ကြိုပါပြီး ဖြစ်သင့်သည်။
How much lap length is needed?
ထပ်ရာအရှည် ဘယ်လောက် လိုလဲ។
It is set by the design, because it depends on the bar grade, the concrete strength, the bar diameter and where in the element the lap falls. It is commonly expressed as a number of bar diameters. Do not take a figure from another job — if the drawing does not state it, ask the engineer rather than guessing, because a short lap is a hidden structural defect.
ဒီဇိုင်းက သတ်မှတ်သည် — ချောင်းအဆင့်၊ ကွန်ကရစ် ခိုင်ခံ့မှု၊ ချောင်းအချင်းနှင့် အစိတ်အပိုင်းအတွင်း ထပ်ရာ ကျရောက်သည့်နေရာအပေါ် မူတည်သောကြောင့် ဖြစ်သည်။ များသောအားဖြင့် ချောင်းအချင်း အရေအတွက်ဖြင့် ဖော်ပြသည်။ အခြားအလုပ်မှ တန်ဖိုးကို မယူပါနှင့် — ပုံစံတွင် မဖော်ပြလျှင် မှန်းဆမည့်အစား အင်ဂျင်နီယာကို မေးပါ။ တိုသော ထပ်ရာသည် ဖုံးကွယ်နေသော တည်ဆောက်ပုံ ချို့ယွင်းချက် ဖြစ်သောကြောင့် ဖြစ်သည်။
How much wastage should I allow?
အလဟဿ ဘယ်လောက် ချန်ထားရမလဲ។
It depends entirely on how the cut lengths divide into 12 metres. Elements at 3 or 4 metres divide cleanly; elements at 4.5 or 5 metres leave a substantial offcut from every bar. Work the cut list against the 12 metre length before ordering — often a small change to a lap position or a bend detail, agreed with the engineer, removes most of the waste.
ဖြတ်အရှည်များသည် ၁၂ မီတာထဲ မည်သို့ စားသည်အပေါ် လုံးဝ မူတည်သည်။ ၃ သို့မဟုတ် ၄ မီတာ အစိတ်အပိုင်းများသည် သန့်သန့် စားသည်။ ၄.၅ သို့မဟုတ် ၅ မီတာ အစိတ်အပိုင်းများသည် ချောင်းတိုင်းမှ များပြားသော အပိုကျန် ချန်ထားသည်။ မမှာမီ ၁၂ မီတာ အရှည်နှင့် ယှဉ်၍ ဖြတ်စာရင်း တွက်ပါ — မကြာခဏ အင်ဂျင်နီယာနှင့် သဘောတူထားသော ထပ်ရာတည်နေရာ သို့မဟုတ် ကွေးအသေးစိတ်တွင် အပြောင်းအလဲငယ်တစ်ခုက အလဟဿ အများစုကို ဖယ်ရှားပေးသည်။
Should I order the exact calculated quantity?
တွက်ထားတဲ့ အတိအကျ ပမာဏကို မှာသင့်လား။
Add a margin. Bars get damaged in handling, a bend goes wrong, a dimension changes on site, and coming back for two bars costs a delivery. A modest allowance on top of the schedule is normal practice and cheaper than a second trip. What is not sensible is ordering far over — rebar left on site in the wet rusts and nobody wants it next season.
အပိုချန်ပါ။ ကိုင်တွယ်စဉ် ချောင်းများ ပျက်စီးသည်၊ ကွေးတစ်ခု မှားသည်၊ လုပ်ငန်းခွင်တွင် အတိုင်းအတာ ပြောင်းသည်၊ ချောင်းနှစ်ချောင်းအတွက် ပြန်လာခြင်းသည် ပို့ဆောင်ခ ကုန်သည်။ ဇယားအပေါ် အသင့်အတင့် ချန်ထားခြင်းသည် ပုံမှန် အလေ့အထဖြစ်ပြီး ဒုတိယအကြိမ် သွားရခြင်းထက် သက်သာသည်။ သင့်တော်ခြင်း မရှိသည်မှာ များစွာ ပိုမှာခြင်း ဖြစ်သည် — စိုစွတ်ရာတွင် လုပ်ငန်းခွင်၌ ကျန်နေသော သံချောင်းသည် သံချေးတက်ပြီး နောက်ရာသီတွင် မည်သူမျှ မလိုချင်တော့ပါ။
What should I bring when ordering rebar?
သံချောင်း မှာတဲ့အခါ ဘာယူလာရမလဲ။
The bar schedule if there is one — it gives diameters, lengths, shapes, quantities and usually the grade in one document. Without it, bring the diameters, the grade, the total length or number of bars per diameter, and say whether a mill certificate is required. Certification has to be asked for at the time of ordering, not afterwards.
ရှိလျှင် ချောင်းဇယား — အချင်းများ၊ အရှည်များ၊ ပုံစံများ၊ အရေအတွက်များနှင့် များသောအားဖြင့် အဆင့်ကို စာရွက်တစ်ခုတည်းတွင် ပေးသည်။ မရှိလျှင် အချင်းများ၊ အဆင့်၊ အချင်းတစ်ခုစီအတွက် စုစုပေါင်းအရှည် သို့မဟုတ် ချောင်းအရေအတွက် ယူလာပြီး၊ စက်ရုံလက်မှတ် လိုအပ်မလို ပြောပါ။ အသိအမှတ်ပြုလက်မှတ်ကို နောက်မှမဟုတ်ဘဲ မှာချိန်တွင် တောင်းရမည်။
Comments
Please sign in to leave a comment.