Choosing a beam is an engineering decision, not a counter decision, and this article will not tell you what size to use. What it can do is explain what the engineer needs to know, what the yard can actually supply, and where the two meet — which is usually where a project loses time.
Beam ရွေးချယ်ခြင်းသည် အင်ဂျင်နီယာ ဆုံးဖြတ်ချက်ဖြစ်ပြီး ကောင်တာ ဆုံးဖြတ်ချက် မဟုတ်ပါ။ ဤဆောင်းပါးသည် ဘယ်အရွယ် သုံးရမည် မပြောပြပါ။ လုပ်နိုင်သည်မှာ အင်ဂျင်နီယာ သိရန်လိုသည်၊ ကုန်တိုက်က တကယ် ပေးနိုင်သည်၊ နှင့် ထိုနှစ်ခု ဆုံရာနေရာကို ရှင်းပြခြင်း ဖြစ်သည် — ထိုနေရာသည် စီမံကိန်းများ အချိန်ဆုံးရှုံးလေ့ရှိသည့် နေရာ ဖြစ်သည်။
What decides the size of a beam?
Beam ရဲ့ အရွယ်ကို ဘာက ဆုံးဖြတ်လဲ။
The span, the load and how much it is allowed to deflect. Doubling the span on the same load needs far more than double the section, because bending increases with the square of the span. That is why a beam that works over three metres can be badly undersized over six, and why nobody should scale a section by eye.
Span၊ ဝန်နှင့် ခွင့်ပြုသော ကွေးညွှတ်မှု ပမာဏ။ ဝန်တူဖြင့် span ကို နှစ်ဆတိုးလျှင် ပစ္စည်းကို နှစ်ဆထက် များစွာ ပို၍ လိုအပ်သည် — ကွေးညွှတ်မှုသည် span ၏ နှစ်ထပ်ကိန်းနှင့်အမျှ တိုးသောကြောင့် ဖြစ်သည်။ ဒါကြောင့် သုံးမီတာတွင် အလုပ်ဖြစ်သော beam သည် ခြောက်မီတာတွင် အရွယ်များစွာ နည်းနေနိုင်ပြီး၊ မည်သူမျှ ပစ္စည်းကို မျက်စိဖြင့် မချဲ့သင့်ပါ။
What information should I bring from the drawing?
ပုံစံကနေ ဘာအချက်အလက် ယူလာရမလဲ။
The section designation, the grade if specified, the length, the quantity, and any note about holes or end preparation. A drawing that says a size but not a grade is incomplete for ordering, because the same section in a higher grade carries more load and costs more. Bring the sheet rather than a photograph of one line of it.
ပစ္စည်းအမည်၊ သတ်မှတ်ထားလျှင် အဆင့်၊ အရှည်၊ အရေအတွက်၊ နှင့် အပေါက်များ သို့မဟုတ် အဖျားပြင်ဆင်မှုအကြောင်း မှတ်ချက်များ။ အရွယ်ပြောပြီး အဆင့် မပါသော ပုံစံသည် မှာယူရန် မပြည့်စုံပါ — အဆင့်မြင့်သော ပစ္စည်းတူသည် ဝန်ပိုခံပြီး ဈေးပိုကြီးသောကြောင့် ဖြစ်သည်။ စာကြောင်းတစ်ကြောင်း၏ ဓာတ်ပုံမဟုတ်ဘဲ စာရွက်ကို ယူလာပါ။
What if the specified section is not in stock?
သတ်မှတ်ထားတဲ့ ပစ္စည်း ကုန်နေရင်ရော။
Do not substitute on your own judgement. Take the available sizes back to whoever specified it — an engineer can usually approve a heavier section quickly, and sometimes a different section entirely with a note about the connections. What causes real problems is a substitution made on site that nobody records, because the next person assumes the drawing was followed.
ကိုယ့်ဆုံးဖြတ်ချက်ဖြင့် အစားမထိုးပါနှင့်။ ရနိုင်သော အရွယ်များကို သတ်မှတ်ခဲ့သူထံ ပြန်ယူသွားပါ — အင်ဂျင်နီယာသည် များသောအားဖြင့် ပိုလေးသော ပစ္စည်းကို မြန်မြန် အတည်ပြုနိုင်ပြီး၊ တစ်ခါတစ်ရံ ဆက်သွယ်မှုများအကြောင်း မှတ်ချက်နှင့်အတူ လုံးဝ မတူသော ပစ္စည်းကို အတည်ပြုသည်။ ပြဿနာ အမှန်တကယ် ဖြစ်စေသည်မှာ မည်သူမျှ မမှတ်တမ်းတင်ဘဲ လုပ်ငန်းခွင်တွင် လုပ်လိုက်သော အစားထိုးမှု ဖြစ်သည် — နောက်လူက ပုံစံအတိုင်း လုပ်ခဲ့သည်ဟု ယူဆသောကြောင့် ဖြစ်သည်။
Does the length affect what I should order?
အရှည်က မှာရမယ့်အရာကို သက်ရောက်လား။
It affects the waste. Sections come in 6000 mm and I beams in 12192 mm, so a job needing 4 metre pieces gets one piece and 2 metres of offcut from a 6 metre length, while 3 metre pieces get two with nothing wasted. Planning the cut list against the stock length before ordering often saves more than negotiating on price.
အလဟဿ ဖြစ်မှုကို သက်ရောက်သည်။ ပစ္စည်းများသည် ၆၀၀၀ မီလီမီတာ၊ I beam များသည် ၁၂၁၉၂ မီလီမီတာဖြင့် လာသဖြင့် ၄ မီတာ အပိုင်းများ လိုသော အလုပ်သည် ၆ မီတာ အရှည်မှ တစ်ပိုင်းနှင့် ၂ မီတာ အပိုကျန် ရသည်။ ၃ မီတာ အပိုင်းများဆိုလျှင် နှစ်ပိုင်း ရပြီး ဘာမျှ မကျန်ပါ။ မမှာမီ စတော့အရှည်နှင့် ယှဉ်၍ ဖြတ်စာရင်း စီစဉ်ခြင်းသည် ဈေးညှိခြင်းထက် မကြာခဏ ပိုချွေတာပေးသည်။
How much does a full length weigh?
အရှည်တစ်ချောင်းလုံး ဘယ်လောက် လေးလဲ။
Read it off the listing — that is what the kilograms per piece figure is for. Our 150x75 I beam at 12192 mm is 792 kg, which needs machinery to move; the 75x38 at the same length is 168 kg, which is a careful four-man lift. Check the weight before planning the delivery and the unloading, not after the lorry arrives.
စာရင်းမှ ဖတ်ပါ — တစ်ချောင်းလျှင် ကီလိုဂရမ် ကိန်းသည် ထိုအတွက် ဖြစ်သည်။ ကျွန်ုပ်တို့ ၁၂၁၉၂ မီလီမီတာ 150x75 I beam သည် ၇၉၂ ကီလိုဖြစ်ပြီး ရွှေ့ရန် စက်ကိရိယာ လိုသည်။ အရှည်တူ 75x38 သည် ၁၆၈ ကီလိုဖြစ်ပြီး ဂရုတစိုက် လူလေးယောက် မြှောက်ရမည် ဖြစ်သည်။ ကုန်ကား ရောက်ပြီးမှ မဟုတ်ဘဲ ပို့ဆောင်မှုနှင့် ချရန် စီစဉ်မီ အလေးချိန်ကို စစ်ပါ။
Is second-hand or reclaimed steel worth buying?
သံမဏိ အဟောင်း ဒါမှမဟုတ် ပြန်သုံးထားတာ ဝယ်တာ တန်လား။
For non-structural work such as fencing, gates and frames, often yes. For anything carrying load, the problem is that you cannot see the grade or the history — a section that has been overloaded, heated or badly cut may look fine. If a drawing or an engineer is involved, buy new with a known grade.
ခြံစည်းရိုး၊ တံခါးနှင့် ဘောင်များကဲ့သို့ တည်ဆောက်ရေးမဟုတ်သော အလုပ်အတွက် မကြာခဏ တန်သည်။ ဝန်ထမ်းသော မည်သည့်အရာအတွက်မဆို ပြဿနာမှာ အဆင့်နှင့် သမိုင်းကြောင်းကို မမြင်နိုင်ခြင်း ဖြစ်သည် — ဝန်လွန်ခဲ့သော၊ မီးရှို့ခဲ့သော သို့မဟုတ် ညံ့ဖျင်းစွာ ဖြတ်ခဲ့သော ပစ္စည်းသည် ကောင်းနေသလို ပုံရနိုင်သည်။ ပုံစံ သို့မဟုတ် အင်ဂျင်နီယာ ပါဝင်နေလျှင် အဆင့်သိရသော အသစ်ကို ဝယ်ပါ။
How is steel priced?
သံမဏိကို ဘယ်လို ဈေးသတ်မှတ်လဲ။
By weight, which is why the kilograms per piece figure appears on every listing. That has a practical consequence: two sections of the same nominal size but different thickness are different prices, and the heavier one is not a free upgrade. Work out the total weight of the order before comparing options — it is the number the price follows.
အလေးချိန်ဖြင့် ဖြစ်သည် — ဒါကြောင့် တစ်ချောင်းလျှင် ကီလိုဂရမ် ကိန်းသည် စာရင်းတိုင်းတွင် ပေါ်သည်။ လက်တွေ့ အကျိုးဆက်တစ်ခု ရှိသည် — အမည်ခံအရွယ်တူပြီး အထူမတူသော ပစ္စည်းနှစ်ခုသည် ဈေးမတူဘဲ၊ ပိုလေးသောဟာသည် အခမဲ့ အဆင့်မြှင့်မှု မဟုတ်ပါ။ ရွေးချယ်စရာများ မနှိုင်းယှဉ်မီ မှာယူမှု၏ စုစုပေါင်း အလေးချိန်ကို တွက်ပါ — ဈေးက လိုက်သော ကိန်း ဖြစ်သည်။
Comments
Please sign in to leave a comment.