Push-in fittings almost never fail on their own. What fails is the tube end, the thread type, or the way the tube was pulled out — and all three are avoidable.Push-in ပစ္စည်းများသည် သူ့ဘာသာသူ ပျက်ခဲပါသည်။ ပျက်တတ်သည်မှာ ပိုက်အဖျား၊ ချည်အမျိုးအစား သို့မဟုတ် ပိုက်ဆွဲထုတ်ပုံ ဖြစ်ပြီး သုံးခုလုံး ရှောင်ရှားနိုင်ပါသည်။
What does the G in MPCF4-G01 mean?
MPCF4-G01 ထဲက G က ဘာကို ဆိုလိုသလဲ
G is a parallel BSPP thread. In that code MPCF is the family (plastic push-in, female straight), 4 is the tube at 4 mm, and G01 is a 1/8 inch BSPP thread. The thread code runs G01 = 1/8" · G02 = 1/4" · G03 = 3/8" across the whole pneumatic range.G သည် ချည်ပြေ BSPP ဖြစ်သည်။ MPCF သည် မိသားစု (ပလတ်စတစ် push-in၊ အတွင်းချည် တည့်)၊ 4 သည် ပိုက် ၄ မီလီမီတာ၊ G01 သည် 1/8 လက်မ BSPP ချည် ဖြစ်သည်။ ချည် code မှာ G01 = 1/8" · G02 = 1/4" · G03 = 3/8" ဖြစ်ပါသည်။
Do I use PTFE tape on a G thread?
G ချည်တွင် PTFE တိပ် သုံးရမလား
No. A parallel G thread does not seal on the thread — it seals on a washer or an O-ring against the face of the port. Tape will not stop a leak and can hold the fitting off its seat. Tapered threads (R or NPT) are the ones that take tape or sealant.မလိုပါ။ ချည်ပြေ G သည် ချည်ပေါ်တွင် မပိတ်ပါ — port မျက်နှာပြင်ကို washer သို့မဟုတ် O-ring ဖြင့် ပိတ်သည်။ တိပ်က ယိုမှုကို မရပ်စေဘဲ ပစ္စည်းကို ခုံမှ ကြွစေနိုင်သည်။ ချည်ကျဉ်း (R၊ NPT) များသာ တိပ် သုံးပါသည်။
Metal or plastic body — does it matter?
သတ္တု သို့မဟုတ် ပလတ်စတစ် — အရေးကြီးသလား
For clean shop air at normal pressure a plastic body such as the MPCF range is fine and costs less. Choose metal where the fitting gets knocked, gets hot, sits near welding, or carries anything but air. Plastic also dislikes solvents — a splash of thinner will craze it and it fails later without warning.သန့်သောလေ ပုံမှန်ဖိအားအတွက် MPCF ကဲ့သို့ ပလတ်စတစ် အဆင်ပြေပြီး ဈေးသက်သာသည်။ ထိခိုက်လွယ်၊ အပူရှိ၊ ဂဟေအနီး သို့မဟုတ် လေမဟုတ်သည့်အရာအတွက် သတ္တုရွေးပါ။ ပလတ်စတစ်သည် solvent ဖြင့် အက်ကွဲပြီး နောင်တွင် သတိပေးမပါဘဲ ပျက်ပါသည်။
Why does a push-in fitting leak air?
Push-in မှ ဘာကြောင့် လေယိုသလဲ
Nearly always the tube, not the fitting. The end must be cut square with a tube cutter, not pinched with side cutters, and the last 20 mm must be free of scratches because the O-ring seals on that surface. A tube gripped in pliers will whistle whatever fitting you use.အမြဲလိုလို ပိုက်ကြောင့်ဖြစ်ပြီး ပစ္စည်းကြောင့် မဟုတ်ပါ။ ပိုက်ဖြတ်ကိရိယာဖြင့် ထောင့်မှန်အောင် ဖြတ်ရမည်၊ ညှပ်ဖြတ်၍ မရပါ။ နောက်ဆုံး ၂၀ မမ တွင် ခြစ်ရာမရှိရပါ — O-ring သည် ထိုနေရာတွင် ပိတ်သောကြောင့် ဖြစ်သည်။
How do I release the tube without breaking the fitting?
ပစ္စည်းမပျက်စေဘဲ ပိုက်ကို ဘယ်လိုဖြုတ်မလဲ
Turn the air off and bleed the line first. Press the collet ring squarely inward and hold it while pulling the tube straight out. Pulling without pressing drives the grip ring harder into the tube — that is what shears collets.ဦးစွာ လေပိတ်ပြီး ဖိအားထုတ်ပါ။ collet ကွင်းကို ညီညာစွာ ဖိထားပြီး ပိုက်ကို တည့်တည့် ဆွဲထုတ်ပါ။ မဖိဘဲဆွဲလျှင် ညှပ်ကွင်းသည် ပိုက်ထဲ ပိုနက်ဝင်သွားပြီး collet ပြတ်ပါမည်။
Can I run oil or water through one?
ဆီ သို့မဟုတ် ရေ သွင်းလို့ရသလား
Air is what they are made for. Low-pressure water is usually tolerated on the plastic ranges; hydraulic oil is not — the pressure is far beyond a collet grip and the seal material is wrong. For oil use a DIN tube fitting or a hose assembly.လေအတွက် ဖြစ်သည်။ ဖိအားနည်းသောရေကို ပလတ်စတစ်များတွင် ခံနိုင်သော်လည်း ဟိုက်ဒရောလစ်ဆီ မရပါ — ဖိအားသည် collet ညှပ်အားထက် များစွာကျော်ပြီး ပိတ်ပစ္စည်း မမှန်ပါ။ ဆီအတွက် DIN ပိုက်ပစ္စည်း သုံးပါ။
What should I tell the counter?
ကောင်တာကို ဘာပြောရမလဲ
Four things: the tube outside diameter in millimetres (4, 6, 8, 10, 12), the thread size and type (G, R or NPT, and 01, 02, 03), the shape, and whether you want metal or plastic.လေးချက် — ပိုက်အပြင်အချင်း မမ (၄၊ ၆၊ ၈၊ ၁၀၊ ၁၂)၊ ချည်အရွယ်နှင့်အမျိုးအစား (G၊ R၊ NPT နှင့် 01၊ 02၊ 03)၊ ပုံသဏ္ဌာန်၊ နှင့် သတ္တုလား ပလတ်စတစ်လား။
Comments
Please sign in to leave a comment.