Brass covers everything that is not steel hydraulic or stainless — air lines, washer lines, fuel, workshop plumbing. The choice comes down to what the tube is made of, because that decides how the fitting grips it.ကြေးဝါသည် သံဟိုက်ဒရောလစ်နှင့် သံမဏိ မဟုတ်သော အရာအားလုံးကို လွှမ်းခြုံပါသည် — လေလိုင်း၊ မှန်သုတ်ရေ၊ ဆီနှင့် အလုပ်ရုံပိုက်လုပ်ငန်း။ ရွေးချယ်မှုသည် ပိုက်ကို မည်သည့်ပစ္စည်းဖြင့် လုပ်ထားသည် ဆိုသည်အပေါ် မူတည်ပါသည် — ၎င်းက ပစ္စည်းက ပိုက်ကို မည်သို့ညှပ်မည်ကို ဆုံးဖြတ်သောကြောင့် ဖြစ်သည်။
Barb, push-in or compression — which should I use?
Barb၊ push-in သို့မဟုတ် compression — ဘယ်ဟာသုံးရမလဲ
Hose barb (B-102) is for soft rubber or PVC hose and needs a clamp over it — cheap, low pressure, fine for water, air tools and washer lines. Push-in (B-31168) suits firm plastic tube and comes apart by hand, good where you service often. Compression and air brake ranges are for rigid nylon or copper and hold the highest pressure of the three.Hose barb (B-102) သည် ပျော့သော ရော်ဘာ သို့မဟုတ် PVC ပိုက်အတွက်ဖြစ်ပြီး အပေါ်မှ clamp လိုသည် — ဈေးသက်သာ၊ ဖိအားနည်း၊ ရေ၊ လေကိရိယာနှင့် မှန်သုတ်ရေပိုက်အတွက် သင့်တော်သည်။ Push-in (B-31168) သည် မာသော ပလတ်စတစ်ပိုက်အတွက်ဖြစ်ပြီး လက်ဖြင့် ဖြုတ်နိုင်သည်။ Compression နှင့် air brake အမျိုးအစားများသည် မာသော နိုင်လွန် သို့မဟုတ် ကြေးနီအတွက်ဖြစ်ပြီး ဖိအားအမြင့်ဆုံး ခံနိုင်သည်။
What is NPTF and how is it different from NPT?
NPTF ဆိုတာဘာလဲ၊ NPT နှင့် ဘာကွာသလဲ
Both are 60 degree tapered American pipe threads and they screw together. The difference is that NPTF is a dry-seal thread — the crests and roots are designed to crush into each other and seal without tape. In practice a light wrap of PTFE tape or a liquid sealant is still normal on our brass fittings, and it does no harm.နှစ်မျိုးလုံး ၆၀ ဒီဂရီ ကျဉ်းသွားသော အမေရိကန်ပိုက်ချည် ဖြစ်ပြီး အချင်းချင်း ဝင်ပါသည်။ ကွာခြားချက်မှာ NPTF သည် dry-seal ချည် ဖြစ်ခြင်း — ချည်ထိပ်နှင့် အောက်ခြေတို့ အချင်းချင်း ဖိကပ်၍ တိပ်မပါဘဲ ပိတ်ရန် ဒီဇိုင်းလုပ်ထားသည်။ လက်တွေ့တွင် PTFE တိပ် အနည်းငယ် သို့မဟုတ် အရည်ပိတ်ဆေး သုံးခြင်းမှာ ပုံမှန်ဖြစ်ပြီး အန္တရာယ် မရှိပါ။
Is a brass fitting suitable for drinking water?
ကြေးဝါပစ္စည်းသည် သောက်ရေအတွက် သင့်တော်သလား
Ordinary brass contains lead, so it is not the right choice for a drinking-water line. For potable water use a lead-free brass or a stainless fitting instead. For air, hydraulic oil, washer fluid, coolant lines and general workshop plumbing, standard brass is the normal and correct choice.သာမန်ကြေးဝါတွင် ခဲ ပါဝင်သဖြင့် သောက်ရေပိုက်အတွက် မသင့်တော်ပါ။ သောက်ရေအတွက် ခဲကင်းသော ကြေးဝါ သို့မဟုတ် သံမဏိပစ္စည်း သုံးပါ။ လေ၊ ဟိုက်ဒရောလစ်ဆီ၊ မှန်သုတ်ရေ၊ ရေအေးပိုက်နှင့် အလုပ်ရုံပိုက်လုပ်ငန်းများအတွက်မူ သာမန်ကြေးဝါသည် မှန်ကန်သော ရွေးချယ်မှု ဖြစ်ပါသည်။
Can I use brass and stainless together?
ကြေးဝါနှင့် သံမဏိ ရောသုံးလို့ရသလား
Mechanically yes, and the threads match. The caution is galvanic corrosion: two different metals in contact with moisture and salt will corrode at the joint over time, the brass going first. Indoors on air or oil it is not a practical problem. Outdoors, near the sea or with anything wet and salty, keep the line in one metal.စက်ပိုင်းအရ ရပါသည်၊ ချည်များလည်း ကိုက်ညီပါသည်။ သတိထားရန်မှာ galvanic သံချေး — သတ္တုနှစ်မျိုး စိုစွတ်မှုနှင့် ဆားရှိသည့်နေရာတွင် ထိနေလျှင် အဆက်နေရာတွင် တဖြည်းဖြည်း ဆွေးပြီး ကြေးဝါက အရင်ပျက်ပါမည်။ အိမ်တွင်း လေ သို့မဟုတ် ဆီလိုင်းတွင် ပြဿနာ မရှိပါ။ အပြင်ဘက်၊ ပင်လယ်နား သို့မဟုတ် ဆားရည်ရှိရာတွင် သတ္တုတစ်မျိုးတည်း သုံးပါ။
How tight should a brass fitting be?
ကြေးဝါပစ္စည်းကို ဘယ်လောက် တင်းသင့်သလဲ
Brass is soft. Tighten to hand tight, then one to two turns with a spanner, and stop when it feels solid. Overtightening splits the female part or strips the thread, and a tapered thread wedges harder the further it goes — so extra force does not cure a leak, it makes the next one worse. If it weeps, back it off, re-tape and try again.ကြေးဝါသည် ပျော့သည်။ လက်ဖြင့် တင်းအောင်လှည့်ပြီး ဝရိန်ဖြင့် တစ်ပတ်မှ နှစ်ပတ် ထပ်တင်းပါ၊ ခိုင်မာသလို ခံစားရလျှင် ရပ်ပါ။ အလွန်အကျွံတင်းလျှင် အတွင်းချည်ပစ္စည်း ကွဲခြင်း သို့မဟုတ် ချည်ပြုတ်ခြင်း ဖြစ်ပါမည်။ ကျဉ်းသွားသောချည်သည် လေးလေးဝင်လေ ပိုကျပ်လေ ဖြစ်၍ အားပိုစိုက်ခြင်းက ယိုမှုကို မပျောက်စေပါ။ ယိုနေလျှင် ပြန်လျှော့၊ တိပ်ပြန်ပတ်ပြီး ပြန်လုပ်ပါ။
What should I tell the counter when ordering?
မှာယူသည့်အခါ ဘာပြောပေးရမလဲ
Five things and the order is settled in one go: the tube outside diameter, the tube material (nylon, copper, rubber hose or plastic), the port thread size, the shape (straight, 90 degree elbow or tee), and what the line carries. If you have the old fitting, the full code on it beats all five.ငါးချက် ပြောပေးလျှင် တစ်ခါတည်း ပြီးပါသည် — ပိုက်၏ အပြင်အချင်း၊ ပိုက်၏ ပစ္စည်းအမျိုးအစား (နိုင်လွန်၊ ကြေးနီ၊ ရော်ဘာပိုက် သို့မဟုတ် ပလတ်စတစ်)၊ port ချည်အရွယ်၊ ပုံသဏ္ဌာန် (တည့်၊ ၉၀ ဒီဂရီကွေး သို့မဟုတ် tee)၊ နှင့် လိုင်းထဲတွင် ဘာစီးဆင်းသည် ဆိုသည်။ ပစ္စည်းဟောင်း ရှိပါက ၎င်းပေါ်ရှိ code အပြည့်သည် အားလုံးထက် ကောင်းပါသည်။
The old fitting has no readable code. What now?
ပစ္စည်းဟောင်းတွင် code မဖတ်နိုင်တော့ပါ။ ဘယ်လိုလုပ်မလဲ
Measure and photograph. Put a caliper across the tube outside diameter and across the thread, then photograph the fitting beside a ruler with the thread end facing the camera. Tube OD plus thread diameter plus the shape is enough for our counter to identify almost any fitting in this range without the code.တိုင်းပြီး ဓာတ်ပုံရိုက်ပါ။ Caliper ဖြင့် ပိုက်၏အပြင်အချင်းနှင့် ချည်အချင်းကို တိုင်းပါ၊ ထို့နောက် ချည်ဘက်ကို ကင်မရာသို့လှည့်၍ ပေတံဘေးတွင် ထား၍ ဓာတ်ပုံရိုက်ပါ။ ပိုက်အပြင်အချင်း၊ ချည်အချင်းနှင့် ပုံသဏ္ဌာန် သုံးခုဖြင့် ကျွန်ုပ်တို့ ကောင်တာမှ code မပါဘဲ ခွဲခြားပေးနိုင်ပါသည်။
Comments
Please sign in to leave a comment.