U bolts and spring pins are sold by measurement, not by vehicle, because the same pickup can carry different hardware depending on how the springs were last repaired. Four figures identify a U bolt and three identify a shackle bush, and all of them come off the old part with a caliper and a tape.
U bolt များနှင့် စပရိန်ပင်များကို ယာဉ်အလိုက်မဟုတ်ဘဲ အတိုင်းအတာဖြင့် ရောင်းသည် — စပရိန်များကို နောက်ဆုံး ဘယ်လို ပြင်ခဲ့သည်ပေါ်မူတည်၍ ပစ်ကပ်တူသည် မတူသော ပစ္စည်းများ ပါနိုင်သောကြောင့် ဖြစ်သည်။ ကိန်းလေးခုက U bolt ကို၊ သုံးခုက shackle bush ကို ခွဲခြားပေးပြီး အားလုံးကို caliper နှင့် ပေတံဖြင့် ပစ္စည်းအဟောင်းမှ ယူနိုင်သည်။
Which four figures identify a U bolt?
ဘယ်ကိန်း လေးခုက U bolt ကို ခွဲခြားပေးသလဲ
Thread diameter and pitch — commonly M12x1.25, M14x1.5, M16x1.5 and M18x1.5 — the inside width across the axle, the leg length from the bend to the thread end, and the bend shape: round for a tube axle, square for a beam. Measure the inside width, not the outside.
ချည်အချင်းနှင့် အကွာအဝေး — အများအားဖြင့် M12x1.25၊ M14x1.5၊ M16x1.5 နှင့် M18x1.5 — ဝင်ရိုးကို ဖြတ်၍ အတွင်းအကျယ်၊ အကွေးမှ ချည်အဆုံးအထိ ခြေတံအလျား၊ နှင့် အကွေးပုံစံ — ပိုက်ဝင်ရိုးအတွက် လုံးဝန်း၊ ချောင်းအတွက် လေးထောင့် — ဖြစ်သည်။ အပြင်မဟုတ်ဘဲ အတွင်းအကျယ်ကို တိုင်းပါ။
What torque do U bolts take?
U bolt များ ဘယ် torque ခံသလဲ
M14 takes about 120 to 160 Nm, M16 about 180 to 250 Nm, tightened in a diagonal pattern in two or three stages so the pack pulls down square. Then drive 50 km loaded and retorque — the leaves settle and the clamp load drops, and a U bolt that is not retorqued is the usual reason a centre bolt shears later.
M14 သည် ၁၂၀ မှ ၁၆၀ Nm ခန့်၊ M16 သည် ၁၈၀ မှ ၂၅၀ Nm ခန့် ခံပြီး အစုံသည် မှန်မှန် ကျလာစေရန် ထောင့်ဖြတ်ပုံစံဖြင့် အဆင့် နှစ်ဆင့် သုံးဆင့်ခွဲ တင်းသည်။ ထို့နောက် ဝန်တင်လျက် ကီလိုမီတာ ၅၀ မောင်းပြီး ပြန်တင်းပါ — ပြားများ တည်ငြိမ်သွားပြီး ညှပ်အား ကျသည်။ ပြန်မတင်းရသော U bolt သည် နောက်ပိုင်း အလယ် bolt ပြတ်ခြင်း၏ ပုံမှန် အကြောင်းရင်း ဖြစ်သည်။
How are shackle bushes measured?
Shackle bush များကို ဘယ်လို တိုင်းမလဲ
Inside diameter, outside diameter and length, in that order — commonly 14 to 20 mm bore, 28 to 40 mm outside and 40 to 70 mm long. Measure the steel shell of the old bush, not the rubber, and measure the eye of the spring once the bush is pressed out, because a hammered eye reads oval.
အတွင်းအချင်း၊ အပြင်အချင်းနှင့် အလျား — ထိုအစီအစဉ်အတိုင်း — ဖြစ်ပြီး အများအားဖြင့် အပေါက် ၁၄ မှ ၂၀ မမ၊ အပြင် ၂၈ မှ ၄၀ မမ၊ အလျား ၄၀ မှ ၇၀ မမ ဖြစ်သည်။ ရာဘာမဟုတ်ဘဲ bush အဟောင်း၏ စတီးအခွံကို တိုင်းပြီး bush ဖိထုတ်ပြီးလျှင် စပရိန်မျက်လုံးကို တိုင်းပါ — တူဖြင့်ရိုက်ထားသော မျက်လုံးသည် ဘဲဥပုံ ဖတ်သောကြောင့် ဖြစ်သည်။
Should rubber or polyurethane bushes be used?
ရာဘာလား polyurethane bush လား
Rubber for a vehicle that carries people and rides on rough roads; polyurethane for one that carries loads every day and where a firmer axle location is wanted. Polyurethane lasts longer against oil but transmits more noise and needs greasing on assembly. Fit what the customer actually uses the vehicle for.
လူသယ်ပြီး ကြမ်းသောလမ်းများပေါ် စီးသော ယာဉ်အတွက် ရာဘာ၊ နေ့စဉ် ဝန်တင်ပြီး ပိုခိုင်မာသော ဝင်ရိုးတည်နေရာ လိုချင်သောနေရာအတွက် polyurethane ဖြစ်သည်။ Polyurethane သည် ဆီကို ပိုခံသော်လည်း အသံ ပိုပို့ပြီး တပ်ဆင်ရာတွင် ဆီချေး လိုသည်။ ဖောက်သည်သည် ယာဉ်ကို တကယ် ဘာအတွက် သုံးသည် အတိုင်း တပ်ပါ။
What is written on the order?
အော်ဒါတွင် ဘာရေးသလဲ
For U bolts: thread and pitch, inside width, leg length, round or square bend, and the quantity — four per axle on most pickups. For bushes: the three dimensions and how many. Adding the vehicle and whether it carries loads lets the counter suggest the right grade rather than just the right size.
U bolt အတွက် — ချည်နှင့် အကွာအဝေး၊ အတွင်းအကျယ်၊ ခြေတံအလျား၊ လုံးဝန်းလား လေးထောင့်လား၊ နှင့် အရေအတွက် — ပစ်ကပ်အများတွင် ဝင်ရိုးလျှင် လေးခု ဖြစ်သည်။ Bush အတွက် — အတိုင်းအတာ သုံးခုနှင့် အရေအတွက် ဖြစ်သည်။ ယာဉ်နှင့် ဝန်တင်မတင် ထည့်ရေးခြင်းသည် ကောင်တာအား အရွယ်မှန်သာမက အဆင့်မှန်ပါ အကြံပေးနိုင်စေသည်။
Can U bolts be made locally?
U bolt များကို ပြည်တွင်းတွင် လုပ်လို့ ရသလား
They are, widely, and the risk is the steel grade. A U bolt is a stretch fastener and needs a known grade — commonly 8.8 or 10.9 — to hold 200 Nm without yielding further in service. A bolt bent from plain mild steel rod holds the first time and loosens within a month. Ask what grade before buying a bent set.
ကျယ်ကျယ်ပြန့်ပြန့် လုပ်ကြပြီး အန္တရာယ်မှာ စတီးအဆင့် ဖြစ်သည်။ U bolt သည် ဆန့်ထွက် တပ်ဆင်ပစ္စည်းဖြစ်ပြီး အသုံးပြုစဉ် ထပ်မဆန့်ဘဲ ၂၀၀ Nm ထိန်းရန် သိထားသော အဆင့် — အများအားဖြင့် 8.8 သို့မဟုတ် 10.9 — လိုသည်။ ရိုးရိုး သံချောင်းမှ ကွေးထားသော bolt သည် ပထမအကြိမ် ထိန်းပြီး တစ်လအတွင်း ချောင်သည်။ ကွေးထားသော အစုံ မဝယ်မီ ဘယ်အဆင့်လဲ မေးပါ။
Comments
Please sign in to leave a comment.